Thank you for the clarification Johannes.
Kind Regards, Nik
Message: 2 Date: Sun, 31 Jan 2016 10:36:37 +0100 From: morgenroth@ibr.cs.tu-bs.de To: nikansell00@gmail.com Cc: ibr-dtn@ibr.cs.tu-bs.de Subject: Re: [ibr-dtn] UDP Convergence Layer Ignored Message-ID: 020001d15c0a$e1eae0f0$a5c0a2d0$@ibr.cs.tu-bs.de Content-Type: text/plain; charset="utf-8"
Just to clarify the confusion.
The parameter “-i <interface>” is a short-cut for a TCP Convergence Layer entry bound on that interface. It just adds an entry to the existing ones within the configuration.
Kind regards,
Johannes Morgenroth
Von: Ibr-dtn [mailto:ibr-dtn-bounces@ibr.cs.tu-bs.de] Im Auftrag von Nik Ansell Gesendet: Montag, 18. Januar 2016 15:11 An: Stephan Rottmann rottmann@ibr.cs.tu-bs.de Cc: ibr-dtn@ibr.cs.tu-bs.de Betreff: Re: [ibr-dtn] UDP Convergence Layer Ignored
Yes, this fixed it.
The -i <interface> dtnd startup option was conflicting with the interface definition in the conf file.
Starting dtnd without the -i option worked fine.
Kind Regards, Nik
On Mon, Jan 18, 2016 at 4:02 PM, Nik Ansell <nikansell00@gmail.com mailto:nikansell00@gmail.com > wrote:
Hi Stephan,
I have just tried again on a brand new installation and observed something strange, hopefully I have found a fix to the problem.
I tried to troubleshoot in stages, this is what I did:
Start dtnd with default conf file - Started OK with no convergence layer
Add custom conf file (below conf1), but do not specify the correct
interface name, also do not start dtnd with -i option - Started OK with UDP Convergence layer (Datagram ConvergenceLayer (UDP) added on eth0:4556)
- Add custom conf file (below conf2) with correct interface name and use
-i option - Fails: (TCP ConvergenceLayer added on eno16777736:4556)
- Revert back to step 2 - Started OK with UDP Convergence layer (Datagram
ConvergenceLayer (UDP) added on eth0:4556)
- Add custom conf file (below conf2) with correct interface name and
_do_not_ use -i dtnd startup option - Works: (Datagram ConvergenceLayer (UDP) added on eno16777736:4556)
I think perhaps the net_eth_interface option in the conf file and the -i dtnd startup option may be conflicting with each other. It appears to start OK using only the net_eth_interface option in the conf file.
When I am logged on to my test bed in a few hours I will try some data transfers and report back.
Kind Regards,
Nik
Conf1:
local_uri = dtn://rx
net_eth_type = dgram:udp
#net_internet = eth0
net_eth_interface = eth0
net_eth_port = 4556
net_interfaces = eth
# Create a route to tx
static1_uri = dtn://tx
static1_port = 4556
static1_address = 10.0.0.1
static1_proto = dgram:udp
static1_immediately = yes # connect immediately to this node
#static1_global = no # this node is only reachable with internet access
Conf2:
local_uri = dtn://rx
net_eth_type = dgram:udp
#net_internet = eno16777736
net_eth_interface = eno16777736
net_eth_port = 4556
net_interfaces = eth
# Create a route to tx
static1_uri = dtn://tx
static1_port = 4556
static1_address = 10.0.0.1
static1_proto = dgram:udp
static1_immediately = yes # connect immediately to this node
#static1_global = no # this node is only reachable with internet access
routing = default
stats_traffic = yes
api_interface = lo
**dtnd startup line and output (UDP starts OK, but not bound to a working nic)
/home/alarm/downloads/ibr-dtn/install/sbin/dtnd -c /home/alarm/downloads/ibr-dtn/source/ibrdtn-repo/ibrdtn/daemon/etc/rx.conf
Mon Jan 18 15:33:05 2016 INFO NativeDaemon: IBR-DTN daemon 1.0.1 (build a5f9012)
Mon Jan 18 15:33:05 2016 INFO Configuration: Configuration: /home/alarm/downloads/ibr-dtn/source/ibrdtn-repo/ibrdtn/daemon/etc/rx.conf
Mon Jan 18 15:33:05 2016 INFO BundleCore: Local node name: dtn://rx
Mon Jan 18 15:33:05 2016 INFO BundleCore: Forwarding of bundles enabled.
Mon Jan 18 15:33:05 2016 INFO BundleCore: Non-singleton bundles are accepted.
Mon Jan 18 15:33:05 2016 INFO NativeDaemon: using bundle storage in memory-only mode
Mon Jan 18 15:33:05 2016 INFO NativeDaemon: API initialized using tcp socket: lo:4550
Mon Jan 18 15:33:05 2016 INFO NativeDaemon: Datagram ConvergenceLayer (UDP) added on eth0:4556
Mon Jan 18 15:33:05 2016 INFO DiscoveryAgent: listen to [ff02::142]:4551
Mon Jan 18 15:33:05 2016 INFO DiscoveryAgent: listen to [224.0.0.142]:4551
Mon Jan 18 15:33:05 2016 INFO DiscoveryAgent: add interface eth0
Mon Jan 18 15:33:05 2016 INFO NativeDaemon: Using default routing extensions
** dtnd startup line and output (Always uses TCP Convergence layer)
/home/alarm/downloads/ibr-dtn/install/sbin/dtnd -c /home/alarm/downloads/ibr-dtn/source/ibrdtn-repo/ibrdtn/daemon/etc/rx.conf -i eno16777736
Mon Jan 18 15:37:33 2016 INFO NativeDaemon: IBR-DTN daemon 1.0.1 (build a5f9012)
Mon Jan 18 15:37:33 2016 INFO Configuration: Configuration: /home/alarm/downloads/ibr-dtn/source/ibrdtn-repo/ibrdtn/daemon/etc/rx.conf
Mon Jan 18 15:37:33 2016 INFO BundleCore: Local node name: dtn://rx
Mon Jan 18 15:37:33 2016 INFO BundleCore: Forwarding of bundles enabled.
Mon Jan 18 15:37:33 2016 INFO BundleCore: Non-singleton bundles are accepted.
Mon Jan 18 15:37:33 2016 INFO NativeDaemon: using bundle storage in memory-only mode
Mon Jan 18 15:37:33 2016 INFO NativeDaemon: API initialized using tcp socket: lo:4550
Mon Jan 18 15:37:33 2016 INFO NativeDaemon: TCP ConvergenceLayer added on eno16777736:4556
Mon Jan 18 15:37:33 2016 INFO DiscoveryAgent: listen to [ff02::142]:4551
Mon Jan 18 15:37:33 2016 INFO DiscoveryAgent: listen to [224.0.0.142]:4551
Mon Jan 18 15:37:33 2016 INFO DiscoveryAgent: add interface eno16777736
Mon Jan 18 15:37:33 2016 INFO NativeDaemon: Using default routing extensions
Kind Regards, Nik
On Mon, Jan 18, 2016 at 2:18 PM, Nik Ansell <nikansell00@gmail.com mailto:nikansell00@gmail.com > wrote:
Hi Stephan,
Thank you for your kind reply.
I originally tried both net_eth_type = udp & static1_proto = udp, but this didn't work.
I will try them both as dgram:udp later and respond back.
Kind Regards, Nik
On Mon, Jan 18, 2016 at 2:00 PM, Stephan Rottmann < rottmann@ibr.cs.tu-bs.de mailto:rottmann@ibr.cs.tu-bs.de > wrote:
Hi Nik,
static1_uri = dtn://rx static1_port = 4556 static1_address = 10.0.1.3 static1_proto = udp
Have you tried dgram:udp at this point?
Best regards, Stephan